Spicer 10 Series U-Joint Service Quick Reference Manual do Utilizador descarregar pdf

Quick Reference GuideQuick Reference Guide

Warnings

Important Note: This document is intended as a "quick

reference" only. Refer to Dana Service Manual DSSM-3264

(3264-04) for detailed warnings and instructions.

• Always follow all safety practices when servicing,

removing and/or installing a driveshaft.

• Always use support straps to prevent the driveshaft

from falling out of the vehicle during removal and

installation.

• Always put the transmission in neutral before

working on the driveshaft.

• Never heat components or use a sledgehammer or

floor jack to remove the driveshaft from the vehicle.

• Do not reuse bearing plate bolts.

• Only replace U-joints with genuine Dana / Spicer

service parts.

Inspection Recommendations

• U-joint inspections should be performed every time a

vehicle comes in for scheduled maintenance.

• Visually inspect for damaged bearing retainers or

stamped straps, loose bearing retainer or strap bolts,

loose companion flange bolts and nuts, loose or

missing spring tabs or spring tab bolts, damaged

tangs

on end

fittings, damaged or missing snap rings

and rotating bearing cups.

• If any of these situations are evident, replacement of

the component is necessary.

• Check all input and output end fittings for looseness.

Take hold of the end fitting with both hands.

Try to move it vertically and horizontally to feel

any looseness.

• There should be less than .006” movement in the

U-joint relative to the end yoke. If looseness in greater

than .006” the U-joint should be replaced.

• Check for the presence of all grease zerks fittings.

Damaged zerks should be replaced. Loose zerks

should be tightened.

Grease Zerks

• Replace damaged zerks.

• Zerk torque 15 ft. lb. (20 Nm)

• Clean zerk nipples before greasing.

Lubrication Intervals

• City - 5,000/8,000 (8,000/12,000Km) or 3 months

• Line Haul/Highway - 10,000/15,000

(16,000/24,000Km) or 3 months

• On/Off Highway - 5,000/8,000 (8,000/12,000Km)

or 3 months

• Reference Dana Service Bulletin J3295 for

additional information

Recommended Lubricant

• Use a quality EP (extreme pressure) grease

• Meeting N.L.G.I.; EP., Grade 2 specifications

• Grease must have operating range of +325°F to -10°F

• Must be compatible with Lithium soap types

Mark Driveshaft (Phasing Marks)

• Mark all mating driveshaft components with a paint

marker to assure proper phasing during reassembly.

• Reassembly of a driveshaft that is out of phase can

cause vibration and failure to driveshaft components.

Spicer

10 Series U-Joint Service

1 2

Resumo do Conteúdo

Página 1 - 10 Series U-Joint Service

Quick Reference GuideQuick Reference GuideWarningsImportant Note: This document is intended as a "quick reference" only. Refer to Dana Serv

Página 2 - Quick Reference Guide

All applications must be approved by the Application Engineering Department. Speciﬁcations and/or design are subject to change without notice or obli

Comentários a estes Manuais

Sem comentários

Spicer 10 Series U-Joint Service Quick Reference Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Para o carro Spicer 10 Series U-Joint Service Quick Reference. Spicer 10 Series U-Joint Service Quick Reference User Manual Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais

Manuais e produtos relacionados com Para o carro Spicer 10 Series U-Joint Service Quick Reference